EC130® H130® - 01 ALL TOOLS
Showing 1–40 of 78 results
![SG 350A93-3206-00 Seal and bush installation, kit](https://sgst.es/wp-content/uploads/2020/12/350A93-3206-20-Seal-bush-installation-block-pic-2-268x268.jpg)
SG 350A93-3206-00 Seal and bush installation, kit
Seal and bush installation, kit
Includes:
SG 350A93-3206-21 Shaft protection tool
SG 350A93-3206-20 Seal / bush installation block
![SG 350A90-11 Starting / Engine Switch, Wrench](https://sgst.es/wp-content/uploads/2023/10/Wrench-Starting-Switch-268x268.jpg)
SG 350A90-11 Starting / Engine Switch, Wrench
Starting / Engine Switch, Nut Wrench
It fits on H125, H130, H135. All 900UN Switch series, 2 N.m Torque value.
1/4 Socket.
AH TOOL 131.
![SG 350A91-3105-02 Sling, Main Rotor Hub](https://sgst.es/wp-content/uploads/2022/03/350A91-3105-02-Sling-Main-Rotor-Hub-268x268.jpg)
SG 350A91-3105-02 Sling, Main Rotor Hub
Device to remove / install the Main Rotor Hub, straps passing under the sleeves.
Maximum admissible lifting load: 500 kg
CE – Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
![SG 8819683000 Wrench](https://sgst.es/wp-content/uploads/2022/03/8819683000-wrench-oil-filter-cover-268x268.jpg)
SG 8819683000 Wrench
Wrench , removal-installation of the oil filter cover.
1/2 Socket wrench
![SG 350A93-3204-00 MGB flange extractor, rotor brake](https://sgst.es/wp-content/uploads/2022/03/350A93-3204-00-Flange-Extractor-268x268.jpg)
SG 350A93-3204-00 MGB flange extractor, rotor brake
Power flange extractor
Brake disc removal.
Tighten the central screw of the tool to remove the brake disk.
![SG 350A93-3206-21 Shaft protection tool](https://sgst.es/wp-content/uploads/2022/01/350A93-3206-21-Shaft-protection-tool-pic1-268x268.jpg)
SG 350A93-3206-21 Shaft protection tool
Shaft protection tool
Protects de the O-ring from the MGB shaft splines and step.
Slides the friction ring and its o-ring into place while preventing damage from MGB shaft splines.
![SG 703A91-0211-01 Shackle, size 16](https://sgst.es/wp-content/uploads/2021/08/703A91-0211-01-Shackle-size-16-268x268.jpg)
SG 703A91-0211-01 Shackle, size 16
Working Load Limit (WLL): 3,25 Ton.
Shackle size: 16 mm - 5/8 "
Yellow pin, 19 mm diameter.
Delivered with CE Certificate of Confirmity.
![SG 350A93-3210-00 MGB sight glass replacement wrench](https://sgst.es/wp-content/uploads/2021/08/350A93-3210-00-Wrench-pic1-268x268.jpg)
SG 350A93-3210-00 MGB sight glass replacement wrench
Wrench, MGB oil sight replacement
Tool used to remove and install the oil sight with the MGB installed or removed from the airframe.
![SG 350A93-3201-00 Bush Extractor, MGB seal](https://sgst.es/wp-content/uploads/2021/07/SG-350a93-3201-00-Pic-268x268.jpg)
SG 350A93-3201-00 Bush Extractor, MGB seal
MGB Seal Bush Extractor .
Tool used to remove the slip ring from the MGB input shaft.
![SG 350A93-3206-20 Seal / bush installation block](https://sgst.es/wp-content/uploads/2020/12/350A93-3206-20-Seal-bush-installation-block-pic-2-268x268.jpg)
SG 350A93-3206-20 Seal / bush installation block
Seal bush installation block, MGB seal
Keeps a distance of 5.7 mm between the visible face of the seal and the external face of the input box.![SG 8816540000 Arriel oil pressure tapping tube module](https://sgst.es/wp-content/uploads/2019/12/816540000-oil-pressure-tapping-tube-pic-268x268.jpg)
SG 8816540000 Arriel oil pressure tapping tube module
Tool required for the inspection and check procedures of the engine oil pressure.
It is used as the interface between the oil pressure tapping ports and a pressure gauge.
Includes: oil hose, pressure gauge and calibration certificate.
Applicability:
Arriel 2B pressure tapping from module 01 (front check point)
Arriel 1 pressure tapping from module 01 + 05 (front and rear check point)
![SG TM2230G001 Starting valve Sealing test tool](https://sgst.es/wp-content/uploads/2019/05/TM2230G001-Starting-valve-Sealing-test-tool-pic2-268x268.jpg)
SG TM2230G001 Starting valve Sealing test tool
SGTM2230G001 TOOL FOR LEAKAGE TEST
Tool used to do a leakage test at P3 inlet of the start electrovalve.
![SG 8816968000 Permeability Measuring Tool](https://sgst.es/wp-content/uploads/2018/07/SG-8816968000-Permeability-1-268x268.jpg)
SG 8816968000 Permeability Measuring Tool
PERMEABILITY MEASURING TOOL, ASSEMBLY
Tool used to check the permeability of the injection wheel.
Arriel 1- All variants, Arriel 2B , 2B1, 2D.
Tool in accordance with Original Equipment Manufacturer Service Letter No. 2279/04/ARRIEL1/78
![Blanking Caps](https://sgst.es/wp-content/uploads/2018/03/h125-blanking-cap-pic1-268x268.jpg)
Blanking Caps
Blanking Caps
Complete set of plugs to safety blank all pipes , hoses, connectors and threads commonly used on engine and airframe (H125, H130, H120 and many other Airbus Helicopters types). Includes small tapered caps specially made for Turbomeca fuel/oil cavities and pipes.![SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping](https://sgst.es/wp-content/uploads/2017/11/TM3199G002-8817027000-tube-for-oil-pressure-tapping-from-module-05-pic1-1-268x268.jpg)
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
Datasheet
Tool required for the inspection and check procedures of the M05 engine oil pressure. It is
used as the interface between the oil pressure tapping part of module 05 and a
pressure gauge.
Includes oil hose and pressure gauge. ![SG 8819987000 Segment Bonding Tool M04](https://sgst.es/wp-content/uploads/2017/08/8819987000-Segment-Bonding-Tool-M04-268x268.jpg)
SG 8819987000 Segment Bonding Tool M04
Datasheet
Tool required for module 04 - Power turbine installation. It is used to hold the two segments in the housing located in the module 04 during the glue curing time.![SG TM5614G001 Guiding Studs](https://sgst.es/wp-content/uploads/2017/08/SG-TM5614G001-Guiding-Studs-pic1-268x268.jpg)
SG TM5614G001 Guiding Studs
Datasheet
Tool required for module 02 - Compressor removal and installation procedures.
It is used to guide and position the module 02 - Compressor in relation to the module 01 - Accessory gearbox + transmission shaft.
Set of 4 guiding studs.
![SG 8818828000 Linking Tool, M03](https://sgst.es/wp-content/uploads/2017/08/8818828000-Linking-Tool-M03-268x268.jpg)
SG 8818828000 Linking Tool, M03
Datasheet
Tool used to protect and hold the rotating assembly of the module 03 - Gas generator. Use it after the removal of the module 02 from the module 03. Module 03 remains in lock position for transportation or storage purposes.![SG 8810131088 Extractors, M04](https://sgst.es/wp-content/uploads/2017/08/SG-8810131088-Extractors-M04-pic1-268x268.jpg)
SG 8810131088 Extractors, M04
Datasheet
Tool required for module 04 - Power turbine removal. The extractors are used to remove the module 04 from the module 03 - Gas generator. Set of three extractors.![SG TM1123G001 Measuring Tool, M02](https://sgst.es/wp-content/uploads/2017/08/TM1123G001-Measuring-tool-M02-p1-268x268.jpg)
SG TM1123G001 Measuring Tool, M02
Datasheet
Tool required to measure the axial bolt stretch during M02 installation.![SG TM1463G001 Special Wrench](https://sgst.es/wp-content/uploads/2017/08/TM1463G001-Special-Wrench-268x268.jpg)
SG TM1463G001 Special Wrench
Datasheet
Tool necessary for the installation of the Module 02 (compressor). It is used to tighten the axial nut of the Module 02.
This tool is used before the extension tightening procedure of the axial bolt.
![SG 8813150000 Tripod, Gas Generator Support.](https://sgst.es/wp-content/uploads/2017/08/8813150000-Gas-generator-support-268x268.jpg)
SG 8813150000 Tripod, Gas Generator Support.
Datasheet
Tool required for module 01 - Accessory gearbox + transmission shaft removal and installation procedures. It is used to hold the gas generator - power turbine assembly when work is done on the module 01.![SG 8813368000 Hoisting Beam, Tilting](https://sgst.es/wp-content/uploads/2017/08/8813368000-Hoisting-beam-tilting-268x268.jpg)
SG 8813368000 Hoisting Beam, Tilting
Data Sheet
This tool is used for M01 - Acc. gearbox + transmission shaft installation/removal procedures (engine in vertical position). Used to handle the gas generator assy by a hoisting beam. Installed on the intermediate casing/turbine casing flanges. CE - Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.![SG 350A90-06 TRDS Bearing Extractor](https://sgst.es/wp-content/uploads/2017/07/SG350A90-06-pic7-268x268.jpg)
SG 350A90-06 TRDS Bearing Extractor
Data Sheet
Removal / installation Tail Rotor Drive Shaft Bearings
Complete set of tools used to remove the bearings from the shaft.![SGK-06 Removal / Installation MGB 4-Contact Bearing](https://sgst.es/wp-content/uploads/2017/03/SGK-06-268x268.jpg)
SGK-06 Removal / Installation MGB 4-Contact Bearing
Data Sheet
Assembly / disassembly Main Gear Box 4-contact bearing
Complete set of tools needed to perform the epicyclic 4-contact bearing replacement. Tools included: SG350A93-3221-00 Bearing box replacement SG350A93-3223-00 Extractor, Bearing Housing SG350A93-3224-00 Retainer / Bearing installation![SG 350A93-3714-00 Swashplate Ball Joint Adjustment Tool](https://sgst.es/wp-content/uploads/2017/03/SG-350A93-3714-00-Swashplate-Ball-Joint-Adjustment-Tool-pic2-268x268.jpg)
SG 350A93-3714-00 Swashplate Ball Joint Adjustment Tool
Adjustment tool, swashplate ball joint
This tool is used to mesure and adjust axial play on swashplate ball joint.
Data Sheet
![SG 350A93-3224-00 Retainer / bearing installation](https://sgst.es/wp-content/uploads/2017/03/350A93-3224-00-Retainer-bearing-installation-268x268.jpg)
SG 350A93-3224-00 Retainer / bearing installation
Retainer / bearing installation
This tool is used to install the planet gear carrier assembly (epicyclic) in the 4-contact bearing.
Data Sheet
SG350A93-3224-20 Pusher SG350A93-3224-21 Mount![SG 350A93-3223-00 Extractor, Bearing Housing](https://sgst.es/wp-content/uploads/2017/03/350A93-3223-00-Extractor-Bearing-Housing-268x268.jpg)
SG 350A93-3223-00 Extractor, Bearing Housing
Bearing / retainer extractor
This tool is used to remove the equipped planet gear cage (epicyclic) from the 4-contact bearing.
Data Sheet
![SG 350A93-3221-00 Bearing box replacement](https://sgst.es/wp-content/uploads/2017/02/350A93-3221-00-Bearing-box-replacement-268x268.jpg)
SG 350A93-3221-00 Bearing box replacement
Bearing / retainer replacement
This tool is used to remove and install the epicyclic 4-contact bearing from the retainer.
Data Sheet
SG350A93-3221-20 Pusher SG350A93-3221-21 Mount![SGHK-4 Cargo Hook Load Test Bench](https://sgst.es/wp-content/uploads/2016/11/SGHK-4-Cargo-Hook-Load-Test-Bench-268x268.jpg)
SGHK-4 Cargo Hook Load Test Bench
Instruction Manual
SGHK-4 has been designed to safety perform proof load tests up to 4500 kg (9923 pounds) in different cargo hook sizes and configurations.- Light and compact heavy duty frame built to last with handles for easy transport.
- Polycarbonate protection shield.
- High resolution analog pressure gauge (calibration certificate included).
- Ready to use, no additional hardware needed.
- Able to test electric swivel bearings.
![SGK-04 MGB input seal replacement](https://sgst.es/wp-content/uploads/2016/10/SGK-04-MGB-input-seal-pic1-268x268.jpg)
SGK-04 MGB input seal replacement
Parts List
Complete set of tools used to replace the Main Gear Box input seal. PRE & POST MOD 077240 Tools included: SG350A93-3201-00 Bush extractor SG350A93-3202-00 Power seal extractor SG350A93-3206-20 Seal / bush installation block SG350A93-3206-21 Shaft protection SG350A93-3200-20 Wrench for MGB power take-off SG350A93-3205-00 Lock wrench![SGK-03 Removal/installation Bidirectional cross-bar Laminated Suspension Blocks](https://sgst.es/wp-content/uploads/2016/10/SGK-03-pic1-268x268.jpg)
SGK-03 Removal/installation Bidirectional cross-bar Laminated Suspension Blocks
Data Sheet
Removal/installation Bidirectional cross-bar Laminated Suspension Blocks.
Complete set of tools needed to replace Laminated Suspension Blocks on Bidirectional Cross-bar.
Tools included:
SG350A93-3800-20 Immobilizing fork, 39mm long
SG350A93-3802-21 Immobilizing fork, 47mm long
SG350A93-3804-00 Wrench M22
SG350A93-3806-00 Wrench M27
![SGK-01 Assembly / disassembly swashplate bearing](https://sgst.es/wp-content/uploads/2016/10/SGK-01-Swashplate-bearing-replacement-268x268.jpg)
SGK-01 Assembly / disassembly swashplate bearing
Data Sheet
Assembly / disassembly swashplate bearing Complete set of tools needed to perform the swasplate bearing replacement. Tools included: SG350A93-3710-00 Rotating Star Tool SG350A93-3712-00 Assembly block, rotating star SG350A93-3713-00 Assembly block, non-rotating star / rotating star SG365A93-3111-01 Rotating star bearing extractor![SGHU-05 Hydraulic Power Unit](https://sgst.es/wp-content/uploads/2016/10/SGHU-05-5-268x268.jpg)
SGHU-05 Hydraulic Power Unit
Data Sheet
SGHU-05 Hydraulic Unit has been designed to safety test AS350®, AS355® and EC130® hydraulic systems. This unit is specially useful to fulfill all requirements and checks related to hydraulic components and associated systems. Ready to use, no additional hardware needed. Light and compact heavy duty frame built to last with wheels for easy transport.![SG TM4229G001 Harness, P & T transmitter](https://sgst.es/wp-content/uploads/2016/10/harness-268x268.jpg)
SG TM4229G001 Harness, P & T transmitter
Data Sheet
Tool required for the inspection and check procedures of the pressure and temperature transmitter It used as the interface between the engine power system, the P & T transmitter and a measuring device. Arriel 2D![SG TM4227G001 Harness, Pressure Transmitter](https://sgst.es/wp-content/uploads/2016/10/harness-268x268.jpg)
SG TM4227G001 Harness, Pressure Transmitter
Data Sheet
This tool is used for the inspection and check procedures of the pressure transmitter. It used as the interface between the engine power system, the pressure transmitter and measuring device. Arriel 2D![SG 8819796000 Harness, P3](https://sgst.es/wp-content/uploads/2016/10/harness-268x268.jpg)
SG 8819796000 Harness, P3
Data Sheet
This tool is used for the inspection and check procedures of P3 air pressure transmitter. It used as the interface between the aircraft power system, the P3 air pressure transmitter and a voltmeter.![SG 350A90-04 | Main Rotor Hub / Mast blanking cap](https://sgst.es/wp-content/uploads/2016/10/SG350A90-04-Mast-cap-pic2-268x268.jpg)
SG 350A90-04 | Main Rotor Hub / Mast blanking cap
Data Sheet
Main Rotor Hub / Mast blanking cap This tool is used to blank the Main Rotor Mast when the Spring Anti-vibrator is removed.![SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE](https://sgst.es/wp-content/uploads/2016/10/8819527000-LOOSENING-TIGHTENING-TOOL-ASSEMBLY-FOR-INLET-CONE-268x268.jpg)
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
Data Sheet
Loosening/Tightening tool assembly for inlet cone This tool is used to install and remove the inlet cone from the module 02 – Compressor.![SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly](https://sgst.es/wp-content/uploads/2016/10/8819114000-TM0038G003-engine-support-pic2-1-268x268.jpg)