View Basket “SG 350A93-3205-00 Lock wrench” has been added to your basket.
SG 8819683000 Wrench
SG 8819683000 Wrench

Wrench , removal-installation of the oil filter cover.

1/2 Socket wrench

   
 397,00 Add to basket
SG 8816540000 Arriel  oil pressure tapping tube module
SG 8816540000 Arriel oil pressure tapping tube module
Tool required for the inspection and check procedures of the engine oil pressure. It is used as the interface between the oil pressure tapping ports and a pressure gauge. Includes: oil hose, pressure gauge and calibration certificate.   Applicability: Arriel 2B pressure tapping from module 01 (front check point) Arriel 1 pressure tapping  from module 01 + 05 (front and rear check point)  
 355,00 Add to basket
SG TM2230G001 Starting valve Sealing test tool
SG TM2230G001 Starting valve Sealing test tool
SGTM2230G001  TOOL FOR LEAKAGE TEST Tool used to do a leakage test at P3 inlet of the start electrovalve.    
 475,00 Add to basket
SG 8816968000 Permeability Measuring Tool
SG 8816968000 Permeability Measuring Tool
PERMEABILITY MEASURING TOOL, ASSEMBLY Tool used to check the permeability of the injection wheel. Arriel 1- All variants, Arriel 2B , 2B1, 2D. Tool in accordance with Original Equipment Manufacturer Service Letter No. 2279/04/ARRIEL1/78
 865,00 Add to basket
Blanking Caps
Blanking Caps
 Blanking Caps
Complete set of plugs to safety blank all pipes , hoses, connectors and threads commonly used on engine and airframe (H125, H130, H120 and many other Airbus Helicopters types). Includes small tapered caps specially made for Turbomeca fuel/oil cavities and pipes.  
 165,00 Add to basket
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
 Datasheet
 
Tool required for the inspection and check procedures of the M05 engine oil pressure. It is used as the interface between the oil pressure tapping part of module 05 and a pressure gauge.
  Includes oil hose and pressure gauge.
 445,00 Add to basket
SG 8819987000 Segment Bonding Tool M04
SG 8819987000 Segment Bonding Tool M04
 Datasheet
 
Tool required for module 04 - Power turbine installation. It is used to hold the two segments in the housing located in the module 04 during the glue curing time.
 675,00 Add to basket
SG TM5614G001 Guiding Studs
SG TM5614G001 Guiding Studs
 Datasheet
 
Tool required for module 02 - Compressor removal and installation procedures.
It is used to guide and position the module 02 - Compressor in relation to the module 01 - Accessory gearbox + transmission shaft.
Set of 4 guiding studs.
 
 187,00 Add to basket
SG 8818828000 Linking Tool, M03
SG 8818828000 Linking Tool, M03
 Datasheet
  Tool used to protect and hold the rotating assembly of the module 03 - Gas generator. Use it after the removal of the module 02 from the module 03. Module 03 remains in lock position for transportation or storage purposes.  
 2.250,00 Add to basket
SG 8810131088 Extractors, M04
SG 8810131088 Extractors, M04
 Datasheet
Tool required for module 04 - Power turbine removal. The extractors are used to remove the module 04  from the module 03 - Gas generator. Set of three extractors.    
 205,00 Add to basket
SG TM1123G001 Measuring Tool, M02
SG TM1123G001 Measuring Tool, M02
 Datasheet
Tool required to measure the axial bolt stretch during M02 installation.    
 682,00 Add to basket
SG TM1463G001 Special Wrench
SG TM1463G001 Special Wrench
 Datasheet
Tool necessary for the installation of the Module 02 (compressor). It is used to tighten the axial nut of the Module 02.
This tool is used before the extension tightening procedure of the axial bolt.
 
 665,00 Add to basket
SG 8813150000 Tripod, Gas Generator Support.
SG 8813150000 Tripod, Gas Generator Support.
 Datasheet
Tool required for module 01 - Accessory gearbox + transmission shaft removal and installation procedures. It is used to hold the gas generator - power turbine assembly when work is done on the module 01.  
 1.058,00 Add to basket
SG 8813368000 Hoisting Beam, Tilting
SG 8813368000 Hoisting Beam, Tilting
Data Sheet
This tool is used for M01 - Acc. gearbox + transmission shaft installation/removal procedures (engine in vertical position). Used to handle the gas generator assy by a hoisting beam. Installed on the intermediate casing/turbine casing flanges. CE - Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.  
 1.195,00 Add to basket
SG TM4229G001 Harness, P & T transmitter
SG TM4229G001 Harness, P & T transmitter
Data Sheet
Tool required for the inspection and check procedures of the pressure and temperature transmitter It used as the interface between the engine power system, the P & T transmitter and a measuring device. Arriel 2D
 745,00 Add to basket
SG TM4227G001 Harness, Pressure Transmitter
SG TM4227G001 Harness, Pressure Transmitter
Data Sheet
This tool is used for the inspection and check procedures of the pressure transmitter. It used as the interface between the engine power system, the pressure transmitter and measuring device. Arriel 2D  
 762,00 Add to basket
SG 8819796000  Harness, P3
SG 8819796000 Harness, P3
Data Sheet
This tool is used for the inspection and check procedures of P3 air pressure transmitter. It used as the interface between the aircraft power system, the P3 air pressure transmitter and a voltmeter.
 762,00 Add to basket
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
Data Sheet
 Loosening/Tightening tool assembly for inlet cone This tool is used to install and remove the inlet cone from the module 02 – Compressor.
 2.013,00 Add to basket
SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly
SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly
Data Sheet
Tool Use Positions
Engine support, storage and modular assembly This tool is used to hold the engine on a trolley to transport or in a container for storage (compatible with Turbomeca containers). It is used as well to hold the engine during modular replacement. It can be used in horizontal or vertical position.  
 1.750,00 Add to basket
SG 8812331000  Gage for igniter plugs positioning
SG 8812331000 Gage for igniter plugs positioning
Data Sheet
Gage for igniter plugs positioning Tool required for the adjustment of the penetration depth of the igniter plugs and start injectors. It is used to measure the thickness of the shims for igniter plugs and start injectors.
 1.048,00 Add to basket
SG 8816082000  Wrench & inmobilizing
SG 8816082000 Wrench & inmobilizing
Data Sheet
Wrench & immobilizing This tool is used to install and remove the nut of the output shaft flange. Tool required for replacement of the output drive shaft mag-seal (M01). Immobilizing span guides Wrench in center position, avoiding any misalignment or slippage.  
 595,00 Add to basket
SG TM4992G001  Wrench & immobilizing
SG TM4992G001 Wrench & immobilizing
Data Sheet
Wrench & immobilizing This tool is used to install and remove the nut of the engine output shaft flange. Tool required for replacement of output drive shaft mag-seal (M01). Immobilizing span guides Wrench in center position, avoiding any misalignment and consequent slippage.  
 595,00 Add to basket
SG 8812954000  Protector Guide
SG 8812954000 Protector Guide
Data Sheet
Protector Guide This tool is used during removal/installation of the free wheel assy. and removal of the seal retainer cage from the reduction gearbox module. It protects the output shaft splines.
 235,00 Add to basket
SG 8818841000  Hoisting Beam
SG 8818841000 Hoisting Beam
Data Sheet
Hoisting Beam M05
Lifting device. This tool is used for module 05 "Reduction gearbox" handling and guiding. Use it to remove, install and replace the module 05 - Reduction gearbox.
CE – Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
 
Equivalent reference Arriel 1  HOISTING FLANGE FOR REDUCTION GEAR M05.
SG 8813988000
 
 729,00 Add to basket
SG 365A91-5400-02  Arriel engine sling
SG 365A91-5400-02 Arriel engine sling
Instruction Manual
Tool Use Positions
  Arriel engine sling Fits on all Arriel engines, 1B, 1D1, 2B, 2B1, 2D. CE - Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.  
 787,00 Add to basket
SG 350A93-5400-00 Support stand, Arriel engine
SG 350A93-5400-00 Support stand, Arriel engine
Data Sheet
Support stand, Arriel engine Hold the engine during MGB removal or  MGB input seal replacement. Flat base surface to avoid any marks or deformations on the engine deck. Anti-slippage rubber material.  
 284,00 Add to basket
SGBST-02 Engine sensor test kit
SGBST-02 Engine sensor test kit
Data Sheet
SGBST-02 has been designed to safety test wide range of Turbomeca® Arrius 2 and Arriel 2 engines pressure switches and transmitters mainly installed in AS350B3®, EC130®, EC120® and EC135® airframes. This tools provides smooth and high accurate pressure adjustment upon all ranges. Easy to pack and transport, does not requires any hydraulic fluid or electrical supply. Simple, fast and clean. The pressure gauge is installed in a Minimess adapter, easy to remove and install. SGBST-02 includes pressure gauge calibration certificate and foam cut hard case.
  • No hydraulic fluids needed
  • Light and compact tool
  • High resolution analog pressure gauge
  • Suitable in all engine sensors
CE – Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
 3.392,00 Add to basket