SG 8816540000 Arriel  oil pressure tapping tube module
SG 8816540000 Arriel oil pressure tapping tube module
Tool required for the inspection and check procedures of the engine oil pressure. It is used as the interface between the oil pressure tapping ports and a pressure gauge. Includes: oil hose, pressure gauge and calibration certificate.   Applicability: Arriel 2B pressure tapping from module 01 (front check point) Arriel 1 pressure tapping  from module 01 + 05 (front and rear check point)  
 250,00 Add to basket
SG TM2230G001 Starting valve Sealing test tool
SG TM2230G001 Starting valve Sealing test tool
SGTM2230G001  TOOL FOR LEAKAGE TEST Tool used to do a leakage test at P3 inlet of the start electrovalve.   MATERIAL:   EN 1.4301 / AISI 304  Stainless Steel grade. SURFACE: Electrolytical Polished. IDENTIFICATION:  P/N laser marking.  
 387,00 Add to basket
SG 8816968000 Permeability Measuring Tool
SG 8816968000 Permeability Measuring Tool
PERMEABILITY MEASURING TOOL, ASSEMBLY Tool used to check the permeability of the injection wheel. Arriel 1- All variants, Arriel 2B , 2B1, 2D. Tool in accordance with Original Equipment Manufacturer Service Letter No. 2279/04/ARRIEL1/78
 472,00 Add to basket
Blanking Caps
Blanking Caps
 Blanking Caps
Complete set of plugs to safety blank all pipes , hoses, connectors and threads commonly used on engine and airframe (H125, H130, H120 and many other Airbus Helicopters types). Includes small tapered caps specially made for Turbomeca fuel/oil cavities and pipes.  
 105,00 Add to basket
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
 Datasheet
 
Tool required for the inspection and check procedures of the M05 engine oil pressure. It is used as the interface between the oil pressure tapping part of module 05 and a pressure gauge.
  Includes oil hose and pressure gauge.
 398,00 Add to basket
SG 8819987000 Segment Bonding Tool M04
SG 8819987000 Segment Bonding Tool M04
 Datasheet
 
Tool required for module 04 - Power turbine installation. It is used to hold the two segments in the housing located in the module 04 during the glue curing time.
 490,00 Add to basket
SG TM5614G001 Guiding Studs
SG TM5614G001 Guiding Studs
 Datasheet
 
Tool required for module 02 - Compressor removal and installation procedures.
It is used to guide and position the module 02 - Compressor in relation to the module 01 - Accessory gearbox + transmission shaft.
Set of 4 guiding studs.
 
 112,00 Add to basket
SG 8818828000 Linking Tool, M03
SG 8818828000 Linking Tool, M03
 Datasheet
  Tool used to protect and hold the rotating assembly of the module 03 - Gas generator. Use it after the removal of the module 02 from the module 03. Module 03 remains in lock position for transportation or storage purposes.  
 1.560,00 Add to basket
SG 8810131088 Extractors, M04
SG 8810131088 Extractors, M04
 Datasheet
Tool required for module 04 - Power turbine removal. The extractors are used to remove the module 04  from the module 03 - Gas generator. Set of three extractors.    
 147,00 Add to basket
SG TM1123G001 Measuring Tool, M02
SG TM1123G001 Measuring Tool, M02
 Datasheet
Tool required to measure the axial bolt stretch during M02 installation.    
 620,00 Add to basket
SG TM1463G001 Special Wrench
SG TM1463G001 Special Wrench
 Datasheet
Tool necessary for the installation of the Module 02 (compressor). It is used to tighten the axial nut of the Module 02.
This tool is used before the extension tightening procedure of the axial bolt.
 
 590,00 Add to basket
SG 8813150000 Tripod, Gas Generator Support.
SG 8813150000 Tripod, Gas Generator Support.
 Datasheet
Tool required for module 01 - Accessory gearbox + transmission shaft removal and installation procedures. It is used to hold the gas generator - power turbine assembly when work is done on the module 01.  
 989,00 Add to basket
SG 8813368000 Hoisting Beam, Tilting
SG 8813368000 Hoisting Beam, Tilting
Data Sheet
This tool is used for M01 - Acc. gearbox + transmission shaft installation/removal procedures (engine in vertical position). Used to handle the gas generator assy by a hoisting beam. Installed on the intermediate casing/turbine casing flanges.  
 978,00 Add to basket
SG 350A90-06 TRDS Bearing Extractor
SG 350A90-06 TRDS Bearing Extractor
 
Data Sheet
Removal / installation Tail Rotor Drive Shaft  Bearings
Complete set of tools used to remove the bearings from the shaft.  
 
 690,00 Add to basket
SGK-06 Removal / Installation MGB 4-Contact Bearing
SGK-06 Removal / Installation MGB 4-Contact Bearing
 
Data Sheet
Assembly / disassembly Main Gear Box 4-contact bearing
Complete set of tools needed to perform the epicyclic 4-contact bearing replacement. Tools included: SG350A93-3221-00 Bearing box replacement SG350A93-3223-00 Extractor, Bearing Housing SG350A93-3224-00 Retainer / Bearing installation  
 
 4.190,00 Add to basket
SG 350A93-3714-00 Swashplate Ball Joint Adjustment Tool
SG 350A93-3714-00 Swashplate Ball Joint Adjustment Tool
Adjustment tool, swashplate ball joint This tool is used to mesure and adjust axial play on swashplate ball joint.    
Data Sheet
 
 1.360,00 Add to basket
SG 350A93-3224-00 Retainer / bearing installation
SG 350A93-3224-00 Retainer / bearing installation
Retainer / bearing installation This tool is used to install the planet gear carrier assembly (epicyclic) in the 4-contact bearing.
Data Sheet
 
 2.032,00 Add to basket
SG 350A93-3223-00 Extractor, Bearing Housing
SG 350A93-3223-00 Extractor, Bearing Housing
  Bearing / retainer extractor This tool is used to remove the equipped planet gear cage (epicyclic) from the 4-contact bearing.
Data Sheet
 
 2.993,00 Add to basket
SG 350A93-3221-00 Bearing box replacement
SG 350A93-3221-00 Bearing box replacement
Bearing / retainer replacement This tool is used to remove and install the epicyclic 4-contact bearing from the retainer.
Data Sheet
 
 613,00 Add to basket
SGHK-4   Cargo Hook Load Test Bench
SGHK-4 Cargo Hook Load Test Bench
Instruction Manual
SGHK-4 has been designed to safety perform proof load tests up to 4500 kg (9923 pounds) in different cargo hook sizes and configurations.
  • Light and compact heavy duty frame built to last with handles for easy transport.
  • Polycarbonate protection shield.
  • High resolution analog pressure gauge (calibration certificate included).
  • Ready to use, no additional hardware needed.
  • Able to test electric swivel bearings.
For further information about SGHK-4 compatibility in different hook types ask to: info@sgst.es
 3.600,00 Add to basket
SGK-04  MGB input seal replacement
SGK-04 MGB input seal replacement
Parts List
Complete set of tools used to replace the Main Gear Box input seal.   Tools included: SG350A93-3203-20 Seal / bush installation block SG350A93-3202-00 Power seal extractor SG350A93-3205-00 Lock wrench SG350A93-3200-20 Wrench for MGB power take-off
 2.250,00 Add to basket
SGK-03 Removal/installation Bidirectional cross-bar Laminated Suspension Blocks
SGK-03 Removal/installation Bidirectional cross-bar Laminated Suspension Blocks
Data Sheet
Removal/installation Bidirectional cross-bar Laminated Suspension Blocks.
Complete set of tools needed to replace Laminated Suspension Blocks on Bidirectional Cross-bar.
Tools included:
SG350A93-3800-20 Immobilizing fork, 39mm long SG350A93-3802-21 Immobilizing fork, 47mm long SG350A93-3804-00 Wrench M22 SG350A93-3806-00 Wrench M27
 760,00 Add to basket
SGK-01  Assembly / disassembly swashplate bearing
SGK-01 Assembly / disassembly swashplate bearing
Data Sheet
Assembly / disassembly swashplate bearing Complete set of tools needed to perform the swasplate bearing replacement. Tools included: SG350A93-3710-00 Rotating Star Tool SG350A93-3712-00 Assembly block, rotating star SG350A93-3713-00 Assembly block, non-rotating star / rotating star SG365A93-3111-01 Rotating star bearing extractor
 2.590,00 Add to basket
SGHU-05 Hydraulic Power Unit
SGHU-05 Hydraulic Power Unit
Data Sheet
SGHU-05 Hydraulic Unit has been designed to safety test AS350®, AS355® and EC130® hydraulic systems. This unit is specially useful to fulfill all requirements and checks related to hydraulic components and associated systems. Ready to use, no additional hardware needed. Light and compact heavy duty frame built to last with wheels for easy transport.
 3.490,00 Add to basket
SG TM4229G001 Harness, P & T transmitter
SG TM4229G001 Harness, P & T transmitter
Data Sheet
Tool required for the inspection and check procedures of the pressure and temperature transmitter It used as the interface between the engine power system, the P & T transmitter and a measuring device. Arriel 2D
 634,00 Add to basket
SG TM4227G001 Harness, Pressure Transmitter
SG TM4227G001 Harness, Pressure Transmitter
Data Sheet
This tool is used for the inspection and check procedures of the pressure transmitter. It used as the interface between the engine power system, the pressure transmitter and measuring device. Arriel 2D  
 648,00 Add to basket
SG 8819796000  Harness, P3
SG 8819796000 Harness, P3
Data Sheet
This tool is used for the inspection and check procedures of P3 air pressure transmitter. It used as the interface between the aircraft power system, the P3 air pressure transmitter and a voltmeter.
 648,00 Add to basket
SG 350A90-04 | Main Rotor Hub / Mast blanking cap
SG 350A90-04 | Main Rotor Hub / Mast blanking cap
Data Sheet
Main Rotor Hub / Mast blanking cap This tool is used to blank the Main Rotor Mast when the Spring Anti-vibrator is removed.
 96,00 Add to basket
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
Data Sheet
 Loosening/Tightening tool assembly for inlet cone This tool is used to install and remove the inlet cone from the module 02 – Compressor.
 1.711,00 Add to basket
SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly
SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly
Data Sheet
Tool Use Positions
Engine support, storage and modular assembly This tool is used to hold the engine on a trolley to transport or in a container for storage (compatible with Turbomeca containers). It is used as well to hold the engine during modular replacement. It can be used in horizontal or vertical position.  
 1.300,00 Add to basket
SG 8812331000  Gage for igniter plugs positioning
SG 8812331000 Gage for igniter plugs positioning
Data Sheet
Gage for igniter plugs positioning Tool required for the adjustment of the penetration depth of the igniter plugs and start injectors. It is used to measure the thickness of the shims for igniter plugs and start injectors.
 980,00 Add to basket
SG 8816082000  Wrench & inmobilizing
SG 8816082000 Wrench & inmobilizing
Data Sheet
Wrench & immobilizing This tool is used to install and remove the nut of the output shaft flange. Tool required for replacement of the output drive shaft mag-seal (M01). Immobilizing span guides Wrench in center position, avoiding any misalignment or slippage.  
 435,00 Add to basket
SG TM4992G001  Wrench & immobilizing
SG TM4992G001 Wrench & immobilizing
Data Sheet
Wrench & immobilizing This tool is used to install and remove the nut of the engine output shaft flange. Tool required for replacement of output drive shaft mag-seal (M01). Immobilizing span guides Wrench in center position, avoiding any misalignment and consequent slippage.  
 435,00 Add to basket
SG 8812954000  Protector Guide
SG 8812954000 Protector Guide
Data Sheet
Protector Guide This tool is used during removal/installation of the free wheel assy. and removal of the seal retainer cage from the reduction gearbox module. It protects the output shaft splines.
 210,00 Add to basket
SG 8818841000  Hoisting Beam
SG 8818841000 Hoisting Beam
Data Sheet
Hoisting Beam M05
Lifting device. This tool is used for module 05 "Reduction gearbox" handling and guiding. Use it to remove, install and replace the module 05 - Reduction gearbox.
   
Equivalent reference Arriel 1  HOISTING FLANGE FOR REDUCTION GEAR M05.
SG 8813988000
 
 620,00 Add to basket
SG 365A91-5400-02  Arriel engine sling
SG 365A91-5400-02 Arriel engine sling
Instruction Manual
Tool Use Positions
  Arriel engine sling Fits on all Arriel engines, 1B, 1D1, 2B, 2B1, 2D.
 690,00 Add to basket
SG 703A97-7210-21 Static test port
SG 703A97-7210-21 Static test port
Data Sheet
Static test port. To be used with any pitot-static test system. Ø9mm hose connection neck.
 75,00 Add to basket
SG 703A95-0505-00 TGB drain plug  220,00 Add to basket
SG 703A95-0508-00  MGB drain plug  250,00 Add to basket