AS350® H125® - 71 POWERPLANT
SG 8819683000 Wrench
Wrench , removal-installation of the oil filter cover.
1/2 Socket wrench
SG 8816540000 Arriel oil pressure tapping tube module
Tool required for the inspection and check procedures of the engine oil pressure. It is used as the interface between the oil pressure tapping ports and a pressure gauge. Includes: oil hose, pressure gauge and calibration certificate. Applicability: Arriel 2B pressure tapping from module 01 (front check point) Arriel 1 pressure tapping from module 01 + 05 (front and rear check point)
SG TM2230G001 Starting valve Sealing test tool
SGTM2230G001 TOOL FOR LEAKAGE TEST Tool used to do a leakage test at P3 inlet of the start electrovalve.
SG 8816968000 Permeability Measuring Tool
PERMEABILITY MEASURING TOOL, ASSEMBLY Tool used to check the permeability of the injection wheel. Arriel 1- All variants, Arriel 2B , 2B1, 2D. Tool in accordance with Original Equipment Manufacturer Service Letter No. 2279/04/ARRIEL1/78
Blanking CapsComplete set of plugs to safety blank all pipes , hoses, connectors and threads commonly used on engine and airframe (H125, H130, H120 and many other Airbus Helicopters types). Includes small tapered caps specially made for Turbomeca fuel/oil cavities and pipes.
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
Tool required for the inspection and check procedures of the M05 engine oil pressure. It is used as the interface between the oil pressure tapping part of module 05 and a pressure gauge.Includes oil hose and pressure gauge.
SG 8819987000 Segment Bonding Tool M04
DatasheetTool required for module 04 - Power turbine installation. It is used to hold the two segments in the housing located in the module 04 during the glue curing time.
SG TM5614G001 Guiding Studs
Tool required for module 02 - Compressor removal and installation procedures.
It is used to guide and position the module 02 - Compressor in relation to the module 01 - Accessory gearbox + transmission shaft.
Set of 4 guiding studs.
SG 8818828000 Linking Tool, M03
DatasheetTool used to protect and hold the rotating assembly of the module 03 - Gas generator. Use it after the removal of the module 02 from the module 03. Module 03 remains in lock position for transportation or storage purposes.
SG 8810131088 Extractors, M04
DatasheetTool required for module 04 - Power turbine removal. The extractors are used to remove the module 04 from the module 03 - Gas generator. Set of three extractors.
SG TM1123G001 Measuring Tool, M02
DatasheetTool required to measure the axial bolt stretch during M02 installation.
SG TM1463G001 Special Wrench
Tool necessary for the installation of the Module 02 (compressor). It is used to tighten the axial nut of the Module 02.
This tool is used before the extension tightening procedure of the axial bolt.
SG 8813150000 Tripod, Gas Generator Support.
DatasheetTool required for module 01 - Accessory gearbox + transmission shaft removal and installation procedures. It is used to hold the gas generator - power turbine assembly when work is done on the module 01.
SG 8813368000 Hoisting Beam, Tilting
Data SheetThis tool is used for M01 - Acc. gearbox + transmission shaft installation/removal procedures (engine in vertical position). Used to handle the gas generator assy by a hoisting beam. Installed on the intermediate casing/turbine casing flanges. CE - Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
SG TM4229G001 Harness, P & T transmitter
Data SheetTool required for the inspection and check procedures of the pressure and temperature transmitter It used as the interface between the engine power system, the P & T transmitter and a measuring device. Arriel 2D
SG TM4227G001 Harness, Pressure Transmitter
Data SheetThis tool is used for the inspection and check procedures of the pressure transmitter. It used as the interface between the engine power system, the pressure transmitter and measuring device. Arriel 2D
SG 8819796000 Harness, P3
Data SheetThis tool is used for the inspection and check procedures of P3 air pressure transmitter. It used as the interface between the aircraft power system, the P3 air pressure transmitter and a voltmeter.
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
Data SheetLoosening/Tightening tool assembly for inlet cone This tool is used to install and remove the inlet cone from the module 02 – Compressor.
SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly
Tool Use PositionsEngine support, storage and modular assembly This tool is used to hold the engine on a trolley to transport or in a container for storage (compatible with Turbomeca containers). It is used as well to hold the engine during modular replacement. It can be used in horizontal or vertical position.
SG 8812331000 Gage for igniter plugs positioning
Data SheetGage for igniter plugs positioning Tool required for the adjustment of the penetration depth of the igniter plugs and start injectors. It is used to measure the thickness of the shims for igniter plugs and start injectors.
SG 8816082000 Wrench & inmobilizing
Data SheetWrench & immobilizing This tool is used to install and remove the nut of the output shaft flange. Tool required for replacement of the output drive shaft mag-seal (M01). Immobilizing span guides Wrench in center position, avoiding any misalignment or slippage.
SG TM4992G001 Wrench & immobilizing
Data SheetWrench & immobilizing This tool is used to install and remove the nut of the engine output shaft flange. Tool required for replacement of output drive shaft mag-seal (M01). Immobilizing span guides Wrench in center position, avoiding any misalignment and consequent slippage.
SG 8812954000 Protector Guide
Data SheetProtector Guide This tool is used during removal/installation of the free wheel assy. and removal of the seal retainer cage from the reduction gearbox module. It protects the output shaft splines.
SG 8818841000 Hoisting Beam
Data SheetHoisting Beam M05
Lifting device. This tool is used for module 05 "Reduction gearbox" handling and guiding. Use it to remove, install and replace the module 05 - Reduction gearbox.
CE – Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
Equivalent reference Arriel 1 HOISTING FLANGE FOR REDUCTION GEAR M05.
SG 365A91-5400-02 Arriel engine sling
Tool Use PositionsArriel engine sling Fits on all Arriel engines, 1B, 1D1, 2B, 2B1, 2D. CE - Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
SG 703A95-0520-01 Engine oil & hydraulic fluid drain plug
Data SheetEngine oil and hydraulic fluid drain plug
SG 350A93-5400-00 Support stand, Arriel engine
Data SheetSupport stand, Arriel engine Hold the engine during MGB removal or MGB input seal replacement. Flat base surface to avoid any marks or deformations on the engine deck. Anti-slippage rubber material.
SG 350A93-3205-00 Lock wrench
Data SheetLock wrench
SGBST-02 Engine sensor test kit
Data SheetSGBST-02 has been designed to safety test wide range of Turbomeca® Arrius 2 and Arriel 2 engines pressure switches and transmitters mainly installed in AS350B3®, EC130®, EC120® and EC135® airframes. This tools provides smooth and high accurate pressure adjustment upon all ranges. Easy to pack and transport, does not requires any hydraulic fluid or electrical supply. Simple, fast and clean. The pressure gauge is installed in a Minimess adapter, easy to remove and install. SGBST-02 includes pressure gauge calibration certificate and foam cut hard case.
- No hydraulic fluids needed
- Light and compact tool
- High resolution analog pressure gauge
- Suitable in all engine sensors