AS350® H125® - 01 ALL TOOLS
Showing 1–40 of 104 results
SG 350A93-3309-00 Flange Extractor TGB
This tool is used to remove the flange from the Tail Gear Box.
SG 350A91-3105-02 Sling, Main Rotor Hub
Device to remove / install the Main Rotor Hub, straps passing under the sleeves.
Maximum admissible lifting load: 500 kg
CE – Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
SG 6801K33-1058-02 Curing tool, bushes TGB Control Lever
Replacement of the bushes on the control lever - Tail Gear Box
Curing tool.
Equivalent Part Number: SG 350A33105802-6801
SG 6803K33-1058-01 Extraction tool, bushes TGB Control Lever
Replacement of the bushes on the control lever - Tail Gear Box
Data Sheet
Equivalent Part Number: SG 350A33105801-6803
SG 8819683000 Wrench
Wrench , removal-installation of the oil filter cover.
1/2 Socket wrench
SG 350A93-3204-00 MGB flange extractor, rotor brake
Power flange extractor
Brake disc removal.
Tighten the central screw of the tool to remove the brake disk.
SG 355A94-3745-01 Swashplate immobilizing assembly.
Main Rotor Flight Controls (dual hydraulic)
Includes: SG355A94-3745-01 Swashplate immobilizing assembly. Qty: 3 units.
SG 350A93-3206-21 Shaft protection tool
Shaft protection tool
Protects de the O-ring from the MGB shaft splines and step.
Slides the friction ring and its o-ring into place while preventing damage from MGB shaft splines.
SG 703A91-0211-01 Shackle, size 16
Working Load Limit (WLL): 3,25 Ton.
Shackle size: 16 mm - 5/8 "
Yellow pin, 19 mm diameter.
Delivered with CE Certificate of Confirmity.
SG 350A93-3210-00 MGB sight glass replacement wrench
Wrench, MGB oil sight replacement
Tool used to remove and install the oil sight with the MGB installed or removed from the airframe.
SG 350A93-3201-00 Bush Extractor, MGB seal
MGB Seal Bush Extractor .
Tool used to remove the slip ring from the MGB input shaft.
SG 350A98-0001-00 Fin attachment tightening wrench, vertical stabilizer
Fin attachment tightening wrench
During some periodic inspections, it is required to check the tightening torque of the screws attaching the upper fin to the tail boom.
This check is difficult to perform due to the missing clearance between the screws to be checked and the Tail Gearbox (TGB).
This tool enables the check the tightening torque of the upper fin attachment screws.
SG 350A93-3206-20 Seal / bush installation block
Seal bush installation block, MGB seal
SG 350A90-10 Long Rod Ball-Joint Replacement tool
This tool kit is used to replace the Long Rod Spherical Bearing.
Drawings in accordance with H125 AMM task 67-21-00,8-2
SG 8816540000 Arriel oil pressure tapping tube module
Tool required for the inspection and check procedures of the engine oil pressure.
It is used as the interface between the oil pressure tapping ports and a pressure gauge.
Includes: oil hose, pressure gauge and calibration certificate.
Applicability:
Arriel 2B pressure tapping from module 01 (front check point)
Arriel 1 pressure tapping from module 01 + 05 (front and rear check point)
SG TM2230G001 Starting valve Sealing test tool
SGTM2230G001 TOOL FOR LEAKAGE TEST
Tool used to do a leakage test at P3 inlet of the start electrovalve.
SG 8816968000 Permeability Measuring Tool
PERMEABILITY MEASURING TOOL, ASSEMBLY
Tool used to check the permeability of the injection wheel.
Arriel 1- All variants, Arriel 2B , 2B1, 2D.
Tool in accordance with Original Equipment Manufacturer Service Letter No. 2279/04/ARRIEL1/78
SG 350A90-08 Accumulator Charging Tool
Data Sheet
SG350A90-08 has been designed to safety charge accumulator installed in AS350B3®, AS355®, EC120®. This tools provides smooth and high accurate pressure adjustment upon all ranges. Easy to pack and transport. SG350A90-08 includes pressure gauge calibration certificate and foam cut hard case- Pressure release function allowed.
Blanking Caps
Blanking Caps
Complete set of plugs to safety blank all pipes , hoses, connectors and threads commonly used on engine and airframe (H125, H130, H120 and many other Airbus Helicopters types). Includes small tapered caps specially made for Turbomeca fuel/oil cavities and pipes.
SG 350A90-07 Vibrex / Chadwick vibration adjustment, removable parts.
Complete set of brackets to perform vibration adjustments on Main Rotor, Tail Rotor Drive Shaft and Tail rotor.
Includes:
3 tracking brackets (blade tips, main rotor).
Swashplate magnetic pick up bracket (main rotor).
Mast lateral accelerometer support (main rotor).
Vertical accelerometer support, forward section of the cabin floor (main rotor).
TRDS photocell bracket.
TRDS accelerometer support.
Tail Rotor Gearbox bracket, photocell and accelerometer (tail rotor).
SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
Datasheet
Tool required for the inspection and check procedures of the M05 engine oil pressure. It is
used as the interface between the oil pressure tapping part of module 05 and a
pressure gauge.
Includes oil hose and pressure gauge. 
SG 8819987000 Segment Bonding Tool M04
Datasheet
Tool required for module 04 - Power turbine installation. It is used to hold the two segments in the housing located in the module 04 during the glue curing time.
SG TM5614G001 Guiding Studs
Datasheet
Tool required for module 02 - Compressor removal and installation procedures.
It is used to guide and position the module 02 - Compressor in relation to the module 01 - Accessory gearbox + transmission shaft.
Set of 4 guiding studs.
SG 8818828000 Linking Tool, M03
Datasheet
Tool used to protect and hold the rotating assembly of the module 03 - Gas generator. Use it after the removal of the module 02 from the module 03. Module 03 remains in lock position for transportation or storage purposes.
SG 8810131088 Extractors, M04
Datasheet
Tool required for module 04 - Power turbine removal. The extractors are used to remove the module 04 from the module 03 - Gas generator. Set of three extractors.
SG TM1123G001 Measuring Tool, M02
Datasheet
Tool required to measure the axial bolt stretch during M02 installation.
SG TM1463G001 Special Wrench
Datasheet
Tool necessary for the installation of the Module 02 (compressor). It is used to tighten the axial nut of the Module 02.
This tool is used before the extension tightening procedure of the axial bolt.
SG 8813150000 Tripod, Gas Generator Support.
Datasheet
Tool required for module 01 - Accessory gearbox + transmission shaft removal and installation procedures. It is used to hold the gas generator - power turbine assembly when work is done on the module 01.
SG 8813368000 Hoisting Beam, Tilting
Data Sheet
This tool is used for M01 - Acc. gearbox + transmission shaft installation/removal procedures (engine in vertical position). Used to handle the gas generator assy by a hoisting beam. Installed on the intermediate casing/turbine casing flanges. CE - Marking and declaration of conformity according to EC-Machinery Directive 2006/42/EC.
SG 350A90-07 Tail Rotor accelerometer support
Data Sheet
Bracket, tail rotor accelerometer and photocell.
Tool used for Tail Rotor Balancing. Suitable for Chadwick and Banner photocells. Precise setting of photocell pointing, avoid twisting problems on balancing charts.
SG 350A90-06 TRDS Bearing Extractor
Data Sheet
Removal / installation Tail Rotor Drive Shaft Bearings
Complete set of tools used to remove the bearings from the shaft.
SGK-06 Removal / Installation MGB 4-Contact Bearing
Data Sheet
Assembly / disassembly Main Gear Box 4-contact bearing
Complete set of tools needed to perform the epicyclic 4-contact bearing replacement. Tools included: SG350A93-3221-00 Bearing box replacement SG350A93-3223-00 Extractor, Bearing Housing SG350A93-3224-00 Retainer / Bearing installation
SG 350A90-05 Landing Gear Skid bumper protectors
Landing Gear Skids protection
Pair of bumper protectors, protect Landing Gear Skid tube from Handling Wheels impacts and damage.
0.5mm thickness, Stainless Steel, matt.
User Guide
SG 350A93-3714-00 Swashplate Ball Joint Adjustment Tool
Adjustment tool, swashplate ball joint
This tool is used to mesure and adjust axial play on swashplate ball joint.
Data Sheet
SG 350A93-3224-00 Retainer / bearing installation
Retainer / bearing installation
This tool is used to install the planet gear carrier assembly (epicyclic) in the 4-contact bearing.
Data Sheet
SG350A93-3224-20 Pusher SG350A93-3224-21 Mount
SG 350A93-3223-00 Extractor, Bearing Housing
Bearing / retainer extractor
This tool is used to remove the equipped planet gear cage (epicyclic) from the 4-contact bearing.
Data Sheet
SG 350A93-3221-00 Bearing box replacement
Bearing / retainer replacement
This tool is used to remove and install the epicyclic 4-contact bearing from the retainer.
Data Sheet
SG350A93-3221-20 Pusher SG350A93-3221-21 Mount
SGHK-4 Cargo Hook Load Test Bench
Instruction Manual
SGHK-4 has been designed to safety perform proof load tests up to 4500 kg (9923 pounds) in different cargo hook sizes and configurations.- Light and compact heavy duty frame built to last with handles for easy transport.
- Polycarbonate protection shield.
- High resolution analog pressure gauge (calibration certificate included).
- Ready to use, no additional hardware needed.
- Able to test electric swivel bearings.
SGK-05 TGB input seal replacement
Parts List
Tail Gear Box input seal replacement Complete set of tools used to replace the magnetic seal on Tail Gear Box. Tools included: SG350A93-3307-00 T.G.B seal holder extractor SG350A93-3305-20 T.G.B Wrench SG350A93-3205-00 Lock wrench SG350A93-3308-00 Exchange seal / seal support