AS350® H125® - 01 ALL TOOLS
Showing 1–40 of 92 results

SG 350A93-3206-20 Seal / bush installation block
Seal bush installation block, MGB seal

SG 350A90-10 Long Rod Ball-Joint Replacement tool
This tool kit is used to replace the Long Rod Spherical Bearing.
Drawings in accordance with H125 AMM task 67-21-00,8-2

SG 8816540000 Arriel oil pressure tapping tube module
Tool required for the inspection and check procedures of the engine oil pressure.
It is used as the interface between the oil pressure tapping ports and a pressure gauge.
Includes: oil hose, pressure gauge and calibration certificate.
Applicability:
Arriel 2B pressure tapping from module 01 (front check point)
Arriel 1 pressure tapping from module 01 + 05 (front and rear check point)

SG TM2230G001 Starting valve Sealing test tool
SGTM2230G001 TOOL FOR LEAKAGE TEST
Tool used to do a leakage test at P3 inlet of the start electrovalve.
MATERIAL: EN 1.4301 / AISI 304 Stainless Steel grade.
SURFACE: Electrolytical Polished.
IDENTIFICATION: P/N laser marking.

SG 8816968000 Permeability Measuring Tool
PERMEABILITY MEASURING TOOL, ASSEMBLY
Tool used to check the permeability of the injection wheel.
Arriel 1- All variants, Arriel 2B , 2B1, 2D.
Tool in accordance with Original Equipment Manufacturer Service Letter No. 2279/04/ARRIEL1/78

SG 350A90-08 Accumulator Charging Tool
Data Sheet
SG350A90-08 has been designed to safety charge accumulator installed in AS350B3®, AS355®, EC120®. This tools provides smooth and high accurate pressure adjustment upon all ranges. Easy to pack and transport. SG350A90-08 includes pressure gauge calibration certificate and foam cut hard case- Pressure release function allowed.

Blanking Caps
Blanking Caps
Complete set of plugs to safety blank all pipes , hoses, connectors and threads commonly used on engine and airframe (H125, H130, H120 and many other Airbus Helicopters types). Includes small tapered caps specially made for Turbomeca fuel/oil cavities and pipes.
SG 350A90-07 Vibrex / Chadwick vibration adjustment, removable parts.
Complete set of brackets to perform vibration adjustments on Main Rotor, Tail Rotor Drive Shaft and Tail rotor.
Includes:
3 tracking brackets (blade tips, main rotor).
Swashplate magnetic pick up bracket (main rotor).
Mast lateral accelerometer support (main rotor).
Vertical accelerometer support, forward section of the cabin floor (main rotor).
TRDS photocell bracket.
TRDS accelerometer support.
Tail Rotor Gearbox bracket, photocell and accelerometer (tail rotor).

SG TM3199G002 / SG 8817027000 Tube, Oil Pressure Tapping
Datasheet
Tool required for the inspection and check procedures of the M05 engine oil pressure. It is
used as the interface between the oil pressure tapping part of module 05 and a
pressure gauge.
Includes oil hose and pressure gauge. 
SG 8819987000 Segment Bonding Tool M04
Datasheet
Tool required for module 04 - Power turbine installation. It is used to hold the two segments in the housing located in the module 04 during the glue curing time.
SG TM5614G001 Guiding Studs
Datasheet
Tool required for module 02 - Compressor removal and installation procedures.
It is used to guide and position the module 02 - Compressor in relation to the module 01 - Accessory gearbox + transmission shaft.
Set of 4 guiding studs.

SG 8818828000 Linking Tool, M03
Datasheet
Tool used to protect and hold the rotating assembly of the module 03 - Gas generator. Use it after the removal of the module 02 from the module 03. Module 03 remains in lock position for transportation or storage purposes.
SG 8810131088 Extractors, M04
Datasheet
Tool required for module 04 - Power turbine removal. The extractors are used to remove the module 04 from the module 03 - Gas generator. Set of three extractors.
SG TM1123G001 Measuring Tool, M02
Datasheet
Tool required to measure the axial bolt stretch during M02 installation.
SG TM1463G001 Special Wrench
Datasheet
Tool necessary for the installation of the Module 02 (compressor). It is used to tighten the axial nut of the Module 02.
This tool is used before the extension tightening procedure of the axial bolt.

SG 8813150000 Tripod, Gas Generator Support.
Datasheet
Tool required for module 01 - Accessory gearbox + transmission shaft removal and installation procedures. It is used to hold the gas generator - power turbine assembly when work is done on the module 01.
SG 8813368000 Hoisting Beam, Tilting
Data Sheet
This tool is used for M01 - Acc. gearbox + transmission shaft installation/removal procedures (engine in vertical position). Used to handle the gas generator assy by a hoisting beam. Installed on the intermediate casing/turbine casing flanges.
SG 350A90-07 Tail Rotor accelerometer support
Data Sheet
Bracket, tail rotor accelerometer and photocell.
Tool used for Tail Rotor Balancing. Suitable for Chadwick and Banner photocells. Precise setting of photocell pointing, avoid twisting problems on balancing charts.
SG 350A90-06 TRDS Bearing Extractor
Data Sheet
Removal / installation Tail Rotor Drive Shaft Bearings
Complete set of tools used to remove the bearings from the shaft.
SGK-06 Removal / Installation MGB 4-Contact Bearing
Data Sheet
Assembly / disassembly Main Gear Box 4-contact bearing
Complete set of tools needed to perform the epicyclic 4-contact bearing replacement. Tools included: SG350A93-3221-00 Bearing box replacement SG350A93-3223-00 Extractor, Bearing Housing SG350A93-3224-00 Retainer / Bearing installation
SG 350A90-05 Landing Gear Skid bumper protectors
Landing Gear Skids protection
Pair of bumper protectors, protect Landing Gear Skid tube from Handling Wheels impacts and damage.
0.5mm thickness, Stainless Steel, matt.
User Guide

SG 350A93-3714-00 Swashplate Ball Joint Adjustment Tool
Adjustment tool, swashplate ball joint
This tool is used to mesure and adjust axial play on swashplate ball joint.
Data Sheet

SG 350A93-3224-00 Retainer / bearing installation
Retainer / bearing installation
This tool is used to install the planet gear carrier assembly (epicyclic) in the 4-contact bearing.
Data Sheet

SG 350A93-3223-00 Extractor, Bearing Housing
Bearing / retainer extractor
This tool is used to remove the equipped planet gear cage (epicyclic) from the 4-contact bearing.
Data Sheet

SG 350A93-3221-00 Bearing box replacement
Bearing / retainer replacement
This tool is used to remove and install the epicyclic 4-contact bearing from the retainer.
Data Sheet

SGHK-4 Cargo Hook Load Test Bench
Instruction Manual
SGHK-4 has been designed to safety perform proof load tests up to 4500 kg (9923 pounds) in different cargo hook sizes and configurations.- Light and compact heavy duty frame built to last with handles for easy transport.
- Polycarbonate protection shield.
- High resolution analog pressure gauge (calibration certificate included).
- Ready to use, no additional hardware needed.
- Able to test electric swivel bearings.

SGK-05 TGB input seal replacement
Parts List
Tail Gear Box input seal replacement Complete set of tools used to replace the magnetic seal on Tail Gear Box. Tools included: SG350A93-3307-00 T.G.B seal holder extractor SG350A93-3305-20 T.G.B Wrench SG350A93-3205-00 Lock wrench SG350A93-3308-00 Exchange seal / seal support
SGK-04 MGB input seal replacement
Parts List
Complete set of tools used to replace the Main Gear Box input seal. Tools included: SG350A93-3203-20 Seal / bush installation block SG350A93-3202-00 Power seal extractor SG350A93-3205-00 Lock wrench SG350A93-3200-20 Wrench for MGB power take-off
SGK-03 Removal/installation Bidirectional cross-bar Laminated Suspension Blocks
Data Sheet
Removal/installation Bidirectional cross-bar Laminated Suspension Blocks.
Complete set of tools needed to replace Laminated Suspension Blocks on Bidirectional Cross-bar.
Tools included:
SG350A93-3800-20 Immobilizing fork, 39mm long
SG350A93-3802-21 Immobilizing fork, 47mm long
SG350A93-3804-00 Wrench M22
SG350A93-3806-00 Wrench M27

SGK-02 Tail Gear Box Control Plate Bearing removal / installation
Data Sheet
Tail Gear Box Control Plate Bearing removal / installation Complete set of tools needed to perform maintenance on TGB Control Plate Bearing. Tools included: SG350A93-3316-20 Rotating star replacement wrench SG350A93-3317-20 Seal fitting tool SG350A93-3320-00 Fit. Bearing seal / stationary sleeve SG350A93-3321-00 Fit. Double-seal /bush SG350A93-3322-00 Fit. Double-seal / cap SG350A93-3323-00 Fit. Non-rotating / rotating sleeve
SGK-01 Assembly / disassembly swashplate bearing
Data Sheet
Assembly / disassembly swashplate bearing Complete set of tools needed to perform the swasplate bearing replacement. Tools included: SG350A93-3710-00 Rotating Star Tool SG350A93-3712-00 Assembly block, rotating star SG350A93-3713-00 Assembly block, non-rotating star / rotating star SG365A93-3111-01 Rotating star bearing extractor
SGHU-05 Hydraulic Power Unit
Data Sheet
SGHU-05 Hydraulic Unit has been designed to safety test AS350®, AS355® and EC130® hydraulic systems. This unit is specially useful to fulfill all requirements and checks related to hydraulic components and associated systems. Ready to use, no additional hardware needed. Light and compact heavy duty frame built to last with wheels for easy transport.
SG TM4229G001 Harness, P & T transmitter
Data Sheet
Tool required for the inspection and check procedures of the pressure and temperature transmitter It used as the interface between the engine power system, the P & T transmitter and a measuring device. Arriel 2D
SG TM4227G001 Harness, Pressure Transmitter
Data Sheet
This tool is used for the inspection and check procedures of the pressure transmitter. It used as the interface between the engine power system, the pressure transmitter and measuring device. Arriel 2D
SG 8819796000 Harness, P3
Data Sheet
This tool is used for the inspection and check procedures of P3 air pressure transmitter. It used as the interface between the aircraft power system, the P3 air pressure transmitter and a voltmeter.
SG 350A90-04 | Main Rotor Hub / Mast blanking cap
Data Sheet
Main Rotor Hub / Mast blanking cap This tool is used to blank the Main Rotor Mast when the Spring Anti-vibrator is removed.
SG 8819527000 LOOSENING/TIGHTENING TOOL ASSEMBLY FOR INLET CONE
Data Sheet
Loosening/Tightening tool assembly for inlet cone This tool is used to install and remove the inlet cone from the module 02 – Compressor.
SG 8819114000 – SG TM0038G003 Engine support, storage and modular assembly
Data Sheet
Tool Use Positions
Engine support, storage and modular assembly This tool is used to hold the engine on a trolley to transport or in a container for storage (compatible with Turbomeca containers). It is used as well to hold the engine during modular replacement. It can be used in horizontal or vertical position.
SG 8812331000 Gage for igniter plugs positioning
Data Sheet
Gage for igniter plugs positioning Tool required for the adjustment of the penetration depth of the igniter plugs and start injectors. It is used to measure the thickness of the shims for igniter plugs and start injectors.